IOTA contest and CY9M DXpedition

I was planning on spending some time this weekend participating in IOTA contest...but...I got called into work and by the time I got home and settled in I was only able to put in about an hour toward the contest. This is the first time I had taken part in the contest and was surprised at the turn out, this is a very busy contest for sure. I had hoped to add to my DXCC count by taking advantage of some of the rare islands. I did hear lots of rare DX but that was as far as it got to making any sort of contact. I found the bands to be so so there was an M6 flare along with an R2 radio black out that did not help out conditions. Despite the conditions I was able to make 8 contacts.
On all my contacts I tried with the lowest power possible and worked my way up until I made contact. If  I was at full output (5 watts) and still could not make contact it was time to move along.

A first time for everything.

I have been a ham for some time now but there are some things I just have not done as of yet......I can now cross off one more "not done thing" and make it DONE!! To some this may be old hack and you have done it hundreds of times. I was on the radio on the weekend and I heard VP2MUQ down in Montserrat, this is not a new DXCC for me but I did notice here was operating split (transmitting on one frequency and receiving on another). I had two strikes against me before I even gave Bob (VP2MUQ) an attempt. He had a large pileup and he was operating split. Up to this point in my have carrier I have never been able to make a contact when the station was operating split. It made me wonder if I was doing the split thing  right or wrong. I had tried many times in the past but was not able to make contact with ANY op using split. Well on July 21 2012 that all came to an end. I setup the offset for the split (the split according to a spot on a cluster) and gave it a go.....nothing.....but there was a large pileup so I gave it a couple more goes. Then at 01:15 UTC VP2MUQ came back to me and before you know it I worked my first split. Well that's it for the post not very exciting to some but to me it was GREAT!! I now know I have been doing the split thing correctly all along. Another item stroked off the ham bucket list.

WOO HOO BY5WJ.....China with QRP!!!

This evening I wanted to get on the  radio to catch some DXCC's for my Diamond ARRL award. The bands were not to full of the DX  that was needed for my DXCC award BUT St.Pierre et Miquelon
is a self-governing territorial overseas collectivity of France and is just outside of Canada, some Canadian hams were there making contacts on 20m!!! It was a DXCC I did not have and it's more or less local....easy peasy.............so I thought. The pileup was huge and I never did make the contact. Later in the evening they were on 40m but I was not able to hear them at all. It seemed I was the only one not able to hear them by the size of the pileup. Oh but earlier China BY5WJ was on the cluster and I thought "what the heck " and holy cow there were LOUD AND CLEAR....I gave them a go but again the pile up was big but I wanted to stick with it as they were just blasting in. While others were making contact I went to QRZ.COM to get some info as I always do...........this is what I found........

Although it would have been satisfying to have worked BY5WJ in China,
I'm sorry but either I sent the wrong call or your ears are defective.  In fact
you worked 6Y5WJ in sunny Jamaica.  If I sent the wrong call then I'm
sorry I need, to practice, a new key, a keyer or radio :) :), either of which
can be sent to me at the above address.  If however you wrote down the
wrong call then I will send YOU either a new pair of headphones, a new
rig or a syringe of warm soapy water:)

Best wishes and 73, Josh

 Oh and I already have Jamaica' well it was good I found out before calling "BY5WJ" for 30 or more minutes. Lesson learned be careful even of the DX cluster spots. As a side note this is a mistake I or anyone could make and it's nice Josh put the info up on QRZ.COM to clear the fog.

HOT STUFF!!!!!

Outdoor temperature reading

We had the hottest day on record today at mid day it climbed to 39C or 102F. When you factored in the humidity it was a nice hot and sticky 47C or 117F.

IARU contest QRP/QRPp event

The IARU 2012 contest has come and gone it was not without atmospheric grumblings. High solar wind at times over 700, Kp index topping out at 6 and this being the aftermath of the class X flare last week. On a brighter note (no pun intended)  the sunspot numbers are up along with the flux readings.

 So how did all this solar mumbo jumbo affect the contesting goals at VE3WDM?? My first goal and last goal of having fun and enjoying the contest was accomplished. As for adding to my DXCC count I only was able to grab one DXCC. The spotting networks were alive with South Pacific and Asia but at VE3WDM nothing at all was heard. My openings seemed to be centered around Europe with the occasional South American tease.

 This contest for me was not about gathering points and contacts. It was taking advantage of a large amount DX and working them with the least amount of power as possible. This meant the contest was slow going and not worrying about total contacts and points. 99% of my contacts were made with QRPp power and some with QRP. Each potential contact started with trying to make the contact with as little as 50Mw's. I had to stop at 50Mw's as my LP100A meter will not measure any lower power output. Back when I ordered and built this meter I never thought I would ever be operating as low as 50Mw's......my thinking was "an attic dipole antenna at QRP of 5 watts I am pushing it" funny how things change over time. I have a device on order that will allow me to measure power output into the nano watts...not that I will ever go there......but you never know!! I was not able to top my all time miles per watt high of  45,868 well maybe next time.

Hendricks 41dB attenuator built and added to the mix

Hendricks attenuator in service

It's Friday and the IARU contest is tomorrow, I had been checking out the propagation throughout the week and things seem to be calming down. Well until yesterday afternoon and the sun released an X1.4 solar flare and if that was not enough a CME as well..... Oh did I mention the CME is headed in our direction as well. So far the solar-terrestrial data seems to be ok. What's not to bad about a proportional hiccup is that it affects all of us, not saying that is a good thing but in the contest  the playing field stays level. This past week my Hendricks 41dB attenuator came in. The assembly was straight forward and was done in no time it

Final testing

tested out ok and I was ready to start using it. The attenuator has to go in series with my antenna  I placed it in series with my antenna B port on the K3. Both feeds from the K3 (antenna A port and B port) go to a LDG DTS-4 switch. Here I am able to place the dipole antenna in series with either antenna Port A or B. I did this as I can set up the K3 to have different settings (power output, filter selections, ATU on or off... etc) for each antenna port. So I select either antenna A or B on the K3 and then on the DTS-4 I select either attenuator in or out.

Solar storms VS QRPp

This week we all have seen sunspot 1515 working overtime producing solar flares.  It has been some time since a sunspot has consistently produced M class flares sometimes 2 or 3 in the same day. As amateurs we like to see rising sunspots, rising Flux numbers and a falling K index. ( as a side note this link is a great index for all those propagation words you wonder about)...BUT....along with an active sun also can come increased solar flare activity, increased solar wind which can bring a downturn for radio conditions. As a QRP/QRPp station I take these conditions as a challenge I also understand that during these times for me DX may mean contacts in the U.S. This week I have tried to get on the radio for a short time each evening. Using the Reverse Beacon Network (RBN) has been a great help giving me an idea which bands were open and just where my CW signal was being heard.  Below is the results of one of my RBN sessions

 20m report

NY3A  in P.A.         11dB
K3MM in M.D.        21dB
WZ7I    in P.A.       18dB 
K1TTT in M.A.       11dB
KB9AMG  in W.I.     9dB       

Most of the time I would be heard in Europe but with conditions the way they are the U.S. seems to be my DX destination for the time being.  I fired up the K3 along with DxLabs. Right off the bat I saw lots of spots for Europe but was not able to hear them on this side of the pond. I then heard an S5 signal from SM5EPO from Sweden. I knew conditions were not that great and after all the RBN confirmed that on 20m's it was the U.S only.........So I dropped the K3's power to 100mW's Heee Heee Heee and gave it a go. SM5EPO came back to me and with a few repeats the contact was complete at 39,111 miles per watt. In the past when conditions were good and I was making QRPp contacts and logging the miles per watt I wanted to see how I would do if conditions were not ideal.

It's time for surgery...........

Ready for action

The time has come for me to open up my Elecraft K3 and preform some surgery. When I purchased the Elecraft P3 to enhance my K3 all was fine until the P3SVGA board was added to the P3. Since the power source for the P3 comes from the K3 with the addition of the P3SVGA board to much power was being  drawn. A

Diode to be removed

resettable fuse in the K3 now and then would trip out. So Elecraft (as they always do) came up with a mod for this problem.  The mod was sent out free BUT it meant opening up my 4k plus radio and removing one SMT diode, inductor and resettable fuse and replacing them with beefed up components. I didn't mind opening up the K3 and adding plug-in components....whole different story when it comes to De-soldering and soldering on the boards!!! For that reason the mod kit sat on my self for about 2 months, after all the P3 was now plugged into it's own power source so the problem was more or less solved.  This weekend in Canada is a long weekend (Canada day) and as always I get bored when I have to much time on my hands.......a little bird whispered in my ear that the board-um can be solved by doing the long over due K3 mod!!!  The board-um got the best of me along with that dam bird!!  I removed the K3 from service and I will say there sure is lots

Fans removed

KPA3 removed

of cables that go into the rig!! With the rig on the bench and beads of sweat starting to form I was off to the races and I hope with a celebration when I hit the finish line!!  As many times in the past I took the covers off and dove in. The first step was to remove the SMT diode easer said then done. This thing is very small it came out with